Author Topic: Slip on Exhaust/ Fuel Processor  (Read 8892 times)

0 Members and 1 Guest are viewing this topic.

Offline Flat-spot

  • Sport Tourer
  • *****
  • Posts: 2518
  • AREA: North Central Area
  • COG#: 11111
  • Membership Level: Active
Re: Slip on Exhaust/ Fuel Processor
« Reply #25 on: December 11, 2014, 09:59:16 am »
JC,  about the cats,  there are 2 of them,  side by side in the header in front of the mid pipe.  Once when I had the muffler and mid pipe off
of the bike,  I fired it up out of curiosity.  Expecting LOUD,  I was shocked at how quiet the cats alone kept it.
'08 C14
There is no such thing as too much ammo, unless you are on fire or trying to swim.

Offline denver6

  • Road Bike
  • ***
  • Posts: 327
  • AREA: Southwest Area
  • COG#: 10119
  • Membership Level: Asst. Area Director
Re: Slip on Exhaust/ Fuel Processor
« Reply #26 on: December 13, 2014, 03:20:42 am »
I just installed the Delkevic DL10.  I was going to get the tri-oval in carbon fiber, but I saw the new slash-cut DL10 and liked that better.  Not too loud - sounds nice!



« Last Edit: December 13, 2014, 03:25:04 am by denver6 »
'12 Black C14
COG 10119
CDA 506
Highlands Ranch, CO

Offline connie_rider

  • "OtP" {retired/assistant} Slave Labor
  • I Need a Life
  • ******
  • Posts: 9691
  • Help us make "OtP" possible! "AGAIN"
  • AREA: South Central Area
  • COG#: 4154
  • Membership Level: Asst. Area Director
Re: Slip on Exhaust/ Fuel Processor
« Reply #27 on: December 13, 2014, 03:20:03 pm »
Looks good... Sounds good!

Ride safe, Ted
14 Connie (Traveler II) / 03 Connie (Buddy)
Gone but not forgotten; 87 and 00 Connies..

If your not already a COGger, "consider becoming one".
Help us make "OtP" possible again!!

Offline Flat-spot

  • Sport Tourer
  • *****
  • Posts: 2518
  • AREA: North Central Area
  • COG#: 11111
  • Membership Level: Active
Re: Slip on Exhaust/ Fuel Processor
« Reply #28 on: December 13, 2014, 05:18:35 pm »
I like that new fat slash-cut!   :great:
'08 C14
There is no such thing as too much ammo, unless you are on fire or trying to swim.

Offline Landon

  • Scooter
  • ***
  • Posts: 290
  • AREA: North Central Area
  • COG#: Forum
  • Membership Level: Forum Subscriber
Re: Slip on Exhaust/ Fuel Processor
« Reply #29 on: May 29, 2015, 12:26:15 am »
I just installed the Delkevic DL10.  I was going to get the tri-oval in carbon fiber, but I saw the new slash-cut DL10 and liked that better.  Not too loud - sounds nice!

http://youtu.be/kN_kQQf8FK8




Could you post a picture of your DL10 with the bags on the bike?
Landon
2012 C14 Arabian Red

Offline denver6

  • Road Bike
  • ***
  • Posts: 327
  • AREA: Southwest Area
  • COG#: 10119
  • Membership Level: Asst. Area Director
Re: Slip on Exhaust/ Fuel Processor
« Reply #30 on: May 29, 2015, 01:00:56 am »
I just installed the Delkevic DL10.  I was going to get the tri-oval in carbon fiber, but I saw the new slash-cut DL10 and liked that better.  Not too loud - sounds nice!

http://youtu.be/kN_kQQf8FK8




Could you post a picture of your DL10 with the bags on the bike?


Sure - give me a few minutes to go out to the garage.

'12 Black C14
COG 10119
CDA 506
Highlands Ranch, CO

Offline denver6

  • Road Bike
  • ***
  • Posts: 327
  • AREA: Southwest Area
  • COG#: 10119
  • Membership Level: Asst. Area Director
Re: Slip on Exhaust/ Fuel Processor
« Reply #31 on: May 29, 2015, 01:36:40 am »
Delkevic DL-10 with bags on.





'12 Black C14
COG 10119
CDA 506
Highlands Ranch, CO

Offline Landon

  • Scooter
  • ***
  • Posts: 290
  • AREA: North Central Area
  • COG#: Forum
  • Membership Level: Forum Subscriber
Re: Slip on Exhaust/ Fuel Processor
« Reply #32 on: May 29, 2015, 10:51:04 am »
Thank you for posting those!  :great:
Landon
2012 C14 Arabian Red

Offline Brant Bandit

  • Mini Bike
  • **
  • Posts: 124
  • AREA: Northeast Area
  • COG#: Forum
  • Membership Level: Forum Subscriber
Re: Slip on Exhaust/ Fuel Processor
« Reply #33 on: February 03, 2016, 03:04:47 am »
OOOO...... that's the pipe I want! IMO the DL10 is the best looking pipe for the C14 and it sounds good too.

Question though...... does the shorter pipe heat the bag up a lot or melt it? lol

Offline denver6

  • Road Bike
  • ***
  • Posts: 327
  • AREA: Southwest Area
  • COG#: 10119
  • Membership Level: Asst. Area Director
Re: Slip on Exhaust/ Fuel Processor
« Reply #34 on: February 03, 2016, 03:15:17 am »
OOOO...... that's the pipe I want! IMO the DL10 is the best looking pipe for the C14 and it sounds good too.

Question though...... does the shorter pipe heat the bag up a lot or melt it? lol

No problem with heat on the surface of the bag. I have never tried to carry ice cream  :) so I don't know if it gets too hot in there.
'12 Black C14
COG 10119
CDA 506
Highlands Ranch, CO

Offline CONAIR

  • Tricycle
  • Posts: 17
  • AREA: North Central Area
  • COG#: Forum
  • Membership Level: Forum Subscriber
Re: Slip on Exhaust/ Fuel Processor
« Reply #35 on: April 10, 2016, 07:08:54 pm »
I have decided to go with a CS1 slip on muffler but I don't want to add a fuel processor or do a reflash. I would like to hear about other members experience with doing a slip on only, any issues ?
Thanks
Delkevic , carbon oval 5lbs touch can with hand around it,its that cool . lov it. no problems ! use old pipe for wheel stop in driveway! lol
wish animals would stay in the forest!